Knob Management

basic

Overview

The Knob Management tab lets you view, pair, and manage the wireless knobs connected to your WVC base station. You can see each knob's connection status, firmware version, and hardware details, and see when a knob has an update.

Note

The Knob Management tab requires firmware 3.6.0 or newer on your WVC. If you don't see this tab, update your firmware. See Firmware Updates.


Viewing Paired Knobs

  1. Connect to your WVC in the LF Audio app.
  2. Tap the gear icon to open device settings.
  3. Open the DEVICE tab, then tap the remote-control icon. The list is headed Knobs.

Each paired knob is listed with:

Field Description
Knob type Single Encoder, Dual Encoder, Concentric Encoder, Quadruple Encoder, WVC Dual PRO Knob, WVC Quad PRO Knob, RTC, WDD-LITE, or BassWatch
Connection status Connected or offline, with signal strength. On firmware 4.6.0 and newer, the wireless link type (Long Range or High Speed) is also shown for connected devices.
Firmware version Current firmware running on the knob
Hardware version Knob hardware revision

Tap a knob entry to expand it and see additional details including manufacture date.

Note

On the Knob Management tab, newer versions of the app list these knobs as WVC Dual PRO Knob or WVC Quad PRO Knob. Older versions list them as Single Encoder or WDD-LITE. The app cannot install a PRO knob update. They update themselves under Advanced > Update Firmware. See PRO Knob Guide: Firmware Updates.

Tip

The link type shows how each device is wirelessly connected. Long Range gives the most range and reliability. High Speed is a faster mode. The base station uses it for strong, nearby links.

Tip

On the WVC-PRO 6, you can also view paired knobs and remove one from the base station touchscreen under Settings > Devices. This requires firmware 4.4.0 or newer.


Adding a New Knob

To pair a new knob or RTC with your WVC:

  1. Tap Add Knob on the Knob Management tab.
  2. The Add Knob page opens with step-by-step instructions. Tap Start Pairing.
  3. On the new knob, go to Advanced > Factory Reset to put it into pairing mode.
  4. The app monitors for the pairing to complete and shows a success message.
Note

Your other knobs and displays stay connected while the base station is in pairing mode.

You can also start pairing from a knob or display you already use:

  • Single, Dual, Concentric or Quad Knob: Advanced > Pair Additional Knob.
  • RTC, WDD-LITE, BassWatch, WVC Dual PRO Knob or WVC Quad PRO Knob: Advanced > Pair Knob. Follow the steps on the screen. When the new knob shows its main screen, choose Done. The RTC shows Done with firmware 4.12.4 or newer. The WDD-LITE, BassWatch and PRO knobs need firmware 4.12.3 or newer.

For detailed pairing instructions, see the Knob Guide.


Removing a Knob

To unpair a knob from your WVC:

  1. Tap the knob in the list to open it.
  2. Tap Remove.
  3. Tap Remove Knob to confirm.

The knob is de-registered and will no longer be able to control the base station. You can re-pair it at any time using the pairing process above.


Per-Knob Firmware Updates

If a knob has an update, its card says Update available. Update it from the knob or display. See WVC Firmware Updates.

Note

The knob must be connected (online) to receive firmware updates. Keep the knob powered on and within range during the update.


Phone Controls on Your Knob

A WVC Dual PRO Knob or WVC Quad PRO Knob with firmware 4.17.1 or newer can be a remote for your phone. See Using the Knob With Your Phone. On an Android phone, the app can also show your music on the knob: the song, the artist, how far into the song you are and the album art. From the knob, you can then skip back or ahead, turn shuffle and repeat on or off, and pick a song from your music app's list.

  1. Pair your phone with the knob. See Pairing Your Phone. On an Android phone you can also pair in the app: tap + Add a device, tap your knob under Available to pair, and type the PIN shown on your knob.
  2. In the app, open Settings. Under Bluetooth, turn on Phone controls on your knob.
  3. Tap Continue. If your phone asks to find nearby devices, allow it.
  4. If the app needs access to your music app, a screen opens. Turn on access for LF Audio. Then go back to the app.

Your knob shows your music while the app shows Showing on your knob. To stop, turn Phone controls on your knob off. The same switch is on the knob's own page. Tap your knob in Garage.

Under the switch, the app may show a note:

  • It says Turn on your knob to see your music on it. The knob is off, out of range, or not in phone mode. Turn it on near your phone, in phone mode.
  • It says your knob needs access to your music app. Tap Open Settings and turn on access for LF Audio.
  • It asks you to allow Nearby devices. Tap Allow.
Note

This works on Android phones only. The switch shows once your phone is paired with a knob in phone mode. On an iPhone, the knob shows the song by itself, with no app.


Knobs and Your Account

When you are signed in to the LF Audio app, every knob that pairs with one of your WVC units is also linked to your account. The knob appears in your customer portal Devices list alongside your other LF Audio hardware, and the portal records the same hardware version, firmware version, and manufacture date the app sees. This makes it easy to look up details about each knob in your system from any browser without having to be physically connected over Bluetooth.

See Account and Sign-In for the full account workflow.